Free tool

Postcard size templates with bleed and safe area

Download a free guide template for each postcard size SmartSQR mails. Every file is a PNG at print resolution with the bleed, the cut line and the safe area marked, so a design made in any program lines up when it is printed and trimmed.

Postcard sizes and templates

These are the postcard sizes SmartSQR prints and mails today. The measurements are the ones the SmartSQR editor uses.

Postcard sizes with bleed, full file size and safe area
PostcardFinished sizeBleed, each sideFull size with bleedSafe area, from the cut lineTemplate
Postcard 4x66 x 4 in0.125 in6.25 x 4.25 in (1875 x 1275 px at 300 dpi)0.25 in
Postcard 4.25x66 x 4.25 in0.125 in6.25 x 4.5 in (1875 x 1350 px at 300 dpi)0.125 in
Postcard 6x8.58.5 x 6 in0.125 in8.75 x 6.25 in (2625 x 1875 px at 300 dpi)0.125 in
Postcard 6x99 x 6 in0.125 in9.25 x 6.25 in (2775 x 1875 px at 300 dpi)0.125 in
Postcard 6x1111 x 6 in0.125 in11.25 x 6.25 in (3375 x 1875 px at 300 dpi)0.25 in

A size with more than one side downloads as a ZIP file holding one PNG per side.

How to read the template

  • Finished size. The size of the postcard after it is cut. This is the size people mean when they say a 6 x 9 postcard.
  • Bleed. Extra artwork past the cut line on every side. Backgrounds and photos that reach the edge must extend into the bleed, so a cut that lands slightly off does not leave a white sliver.
  • Cut line. Where the card is trimmed. It is the edge of the finished size.
  • Safe area. The space inside the cut line where text, logos and QR codes belong. Anything outside it can be trimmed off or sit too close to the edge.

On the address side, the template also marks the area the postal service needs clear for the address and barcodes, where the size has one. Keep artwork, and above all QR codes, out of it.

How to use a template in your design program

  1. Download the template for your postcard size and open it as the bottom layer of a new file. Do not resize it.
  2. Set your document to the template's full size, bleed included, at the resolution in the table.
  3. Run backgrounds and photos to the outer edge of the bleed.
  4. Keep text, logos and the QR code inside the safe area.
  5. Hide or delete the template layer before you export, so the guides do not print.

Adding a QR code? Make one with the free QR code generator, and read how to size and place it in QR codes for direct mail.

Or skip the template

The SmartSQR editor has these guides built in. Pick a postcard size and the bleed and safe-area guides are already on the canvas. Designing is free; you pay per piece when you mail.

Frequently asked questions

What is bleed on a postcard?

Bleed is artwork that extends past the cut line on every side. Printed sheets are trimmed in stacks and the cut can shift slightly, so a background that stops at the cut line can show a thin white edge. Extending it into the bleed prevents that.

What is the safe area?

The safe area is the part of the card far enough inside the cut line that nothing in it will be trimmed. Keep text, logos and QR codes inside it.

Which programs can I use these templates in?

Any program that can place a PNG image and set a document size in inches or pixels. Place the template on the bottom layer, design on top, then hide it before exporting.

Do I need a template if I design in SmartSQR?

No. The SmartSQR editor shows the same bleed and safe-area guides on the canvas for whichever size you pick.

Where can a QR code go on a postcard?

Inside the safe area, next to the offer, and away from the address side's mailing panel. Print it at least 0.8 inch square.

More free tools